6 Ways How to Finish Serger Tails

How to Finish Serger Tails

Today, I’ll show you how to finish serger tails. For those that use a serger, we are always faced with the same dilemma after each stitch… “what do I do with the chains at the beginning and end!?” Well, that’s what I’m here for!! In this blog I’m going to go over six ways you can use to finish your serger tails. Some are easy, others take more time but are tidier. Good luck and I hope you learn a little something new today!

6 Methods of How to Finish Serger Tails

Finishing Serger Tails Method 1: Serging over existing tails.

I think I’m cheating by counting this as a method, but I’ll discuss it here because it’s probably the most common way to finish your tails. Many patterns finish tails this way just by going through the steps. For example, shoulder seams are generally finished using this method by the neckband or a hood on one side, and sleeves or armbands on the other.

6 Ways How to Finish Serger Tails   6 Ways How to Finish Serger Tails

Finishing Serger Tails Method 2: Weaving the tails.

This is the most popular method, and is the one I use when my tails aren’t finished with Method 1. Although I find this the easiest way to finish my tails, it leaves a bit of bulk along the seams. Depending on what you’re sewing or where the seam is located, this may not be desired, so in those cases, I recommend using another method.

Once you’ve serged your seam, chain off your stitches 4”-6” by pulling your garment away from the machine with it still running to allow plenty of thread to work with. After the chain has been cut from the machine, I run my fingers gently over the remaining tail from the seam to the cut ends to lengthen the threads as much as they’ll go, then trim them down to the same length. This makes threading them through a needle much easier. I recommend using an embroidery/hand-sewing/large-eye needle if you have one since you will be threading 3 or 4 threads through the eye.

Starting at the edge of the seam, weave your needle and tail back through the stitches. I’ll generally go in about an inch, pull the needle and thread out, loop it around the last stitch it went under, then weave the needle back through another inch. I feel this secures the thread better with less chance of it working its way out over time.

6 Ways How to Finish Serger Tails

6 Ways How to Finish Serger Tails

Pull your needle and thread all the way through, then carefully clip off the remaining tail. I add a dab of Fray Check (you can use clear fingernail polish or another form of adhesive as well) to the clipped portion to give it that added security. Done!!

6 Ways How to Finish Serger Tails

Finishing Serger Tails Method 3: Unraveling and tying off the threads.

This is the first of two methods that involve tying off the ends. With this one, carefully unravel the tail at the end of the seam, separating them into 3 or 4 threads as applicable. Split them in half, (2 and 2, or 2 and 1), then tie them in to a double knot. Add a dab of Fray Check for safe keeping, and there you have it!

6 Ways How to Finish Serger Tails

6 Ways How to Finish Serger Tails

Finishing Serger Tails Method 4: Tying threads together.

The goal of this method is to tie all of the threads together as close to the edge of the seam as possible, without unraveling them as in the previous step. It’s not very easy knotting it off without an aid of some sort, so grab your embroidery needle (the one with the big-eye) or something similar to help.

Loop the tail around itself as though you are going to tie the knot, but before you pull it tight, place the needle inside the loop to anchor the threads and position the knot where you want it. Pull tight to knot and remove the needle.

6 Ways How to Finish Serger Tails

6 Ways How to Finish Serger Tails

Carefully cut off the excess thread, dab on some Fray Check, and you’re finished!

6 Ways How to Finish Serger Tails

Finishing Serger Tails Method 5: Serging over the end.

This method is a bit more difficult, and requires an attention to detail and practice to perfect. There are several steps (but I have pictures for you!)

(1) Serge until you reach the end of your seam, allowing maybe a stitch or two at the edge of the fabric.

6 Ways How to Finish Serger Tails

(2) Lift your foot, roll the serged seam towards you, and place it back under the foot, preparing to serge in the opposite direction. The serged seam will be directly alongside the knife.

6 Ways How to Finish Serger Tails

6 Ways How to Finish Serger Tails

(3) Disengage the knife, then feed the garment back through, serging over the end about an inch or two.

6 Ways How to Finish Serger Tails

(4) Lift the foot and carefully pull your fabric away from the foot/needles.

6 Ways How to Finish Serger Tails

(5) Carefully trim the excess tail. All done! (Don’t forget to re-engage your knife before your next seam!)

6 Ways How to Finish Serger Tails

6 Ways How to Finish Serger Tails

Finishing Serger Tails Method 6: Cut off the excess.

This last step takes the least amount of time, but requires Fray Check to secure.

With this method, simply clip the tail at the edge of the fabric and secure with adhesive. I don’t believe this technique is totally effective – with nothing by adhesive to secure it, it may unravel after a few washes.

how to finish serger tails

6 Ways How to Finish Serger Tails

And there you have it! Hopefully one or two of these methods of how to finish serger tails proves useful to you.

Do you use a method other than the ones I described above? I’d love to learn something new, so please share it if so!


Other Tutorials

Before you leave, make sure to join our Facebook Group. Also, if you enjoyed this – you might like some of Peekaboo Pages other posts:

11 Responses

  1. I use a needle with a large eye at each end that is made for serger tails. Push one end into stitches, then thread short tails into 2nd eye and pull through. My question is how to make the ends look good when serging a circular area- I seem to get a lumpy overlap

  2. Stephanie, I normally use the second method. But occasionally I do a combination of the third and fourth. I unravel the threads, thread them through a darning needle and weave them back into the stitching. I never cut them off at the end.

  3. When I serge over other seams to “finish” the ends, it looks like it works great. However, as the knit stretches, the seam that has had the end of it trimmed by the serger then begins to unravel. How do you avoid having your seams stretch and unravel the seam?

  4. I was taught by a person who owned a serger before I did, to just grab one of the lower looper threads and pull until it tightens up at the seam, then cut the threads. Sometimes, I will fold the tail back on the seam, take it to my regular machine and zig zag in the seam allowance for about half an inch and trim any extra. That seems to work really well. Anyone else use these methods?

    1. I use a version of the zig-zag method as well. I take all four of the serger threads lay them back over the serged edge and zig-zag apprx 1/2″, and then cut the tails. It locks in the threads and provides a clean finish.

  5. I use my sewing machine…….leave a tail a couple inches long, take to the machine, flip the tail back over the edge and zig zag just a few stitches near the end… cut off the remainder and voila… 5 seconds, never comes loose, good to go.

  6. This may of been helpful information but there were so many ads that kept covering your photos and embedded links that kept taking me to other sites that it became a hassle to try to read your blog post. I can’t believe I actually made it to the bottom of this page.

    1. Bummer, that’s really annoying! Try reading on a computer or tablet where the ads are on the sides rather than in the middle of the blog. Hope that helps!

    2. Trick for reading stuff without the annoying ads: up at the top of your web browser page, just to the left of the “www” should be an icon of 5 horizontal lines. Click on that. It will transform the page into pure text. No distracting ads.

  7. Hi Stephanie! Thanks for this post it is very helpful. I have a question.. I am trying to make a scarf serging two different pieces of knit fabric together but the serged edge will be showing around the outside. I am having some difficulty finishing the edges to make them not noticeable to the eye. Do you think a Zig zag Stich over the tail would work to secure the ends and prevent unraveling? Thank you!

Leave a Reply

Your email address will not be published. Required fields are marked *