If you have little ones they will love these diy floor pillows!
I originally shared this over at The Ribbon Retreat and now I’m back to share it here as party of the Play Room tour! If you missed Monday’s post be sure to hop on over and check out the Dr. Suess Theme play room. More to come next week 🙂
The DIY floor pillows are perfect for having a little snack break on…
Or having a little rest
Or if you have older kids these are also perfect for jumping! Anne loves jumping up and down on these without getting in trouble 🙂
They have a zipper so you can remove the stuffing if you need to wash them. Not that my toddlers ever spill on things 🙂 And a fun little handle for toting them around.
DIY Floor Pillows Instructions
Let’s get started!
I made 2 diy floor pillows but here’s the supply list for one 20″ floor cushion:
2/3 yard main fabric (this is the top, bottom and handle)
1/2 yard contrast fabric for side panels (my cushion was 6″ tall. For a lower cushion you could get away with 1/3 yard)
2 yards Medium or Heavyweight Interfacing: I added this too all of my pieces before starting
4 yards of piping (optional)
Foam: This can be pricey at the craft store. I cut up an old mattress topper and I’ve heard you can also buy a big slab at Home Depot for $20 and that would give you enough for 2 cushions. You can find it in the camping section
Zipper: I used the 14″ zippers and with my heavy duty foam it was a bit of a squeeze so you may want to go a bit bigger
1. Cut out a top and bottom circle with a 20″ diameter. I cut a string to 10″ and pinned it in the center and taped a pen to the other end to create a make shift compass (remember those???). I then folded it in quarters to make sure everything lined up well and cut them out. If you want to do piping baste that to the outer edge overlapping your 2 ends. I find it’s easiest to use my zipper foot for this step.
2. For a 20″ circle your finished side panel needs to be 61.25″. I made my panels 7″ tall based on the height of the foam I was using (I wanted two 3″ layers in each cushion). If you get a nice long zipper you can go with two 31.5″ panels and use 1/2″ seam allowances to join them together. I’ll leave the rest of the math up to you based on your zipper size 🙂
The zipper panel needs to be 1″ taller than your other panels (mine was 8″) and 1″ longer than your zipper length. Cut the panel in half so you have 2 long skinny pieces and then with right sides together sew one side of the zipper to the 1st piece.
3. Sew the other side of your zipper to the 2nd zipper panel with right sides together.
You’ll now have this…
4. Flip it over and topstitch the zipper to the fabric right along the zipper edge
5. For an extra pop you can add piping along both short edges of the zipper panel
5. I cut my handles to 9 x 5″. Press all edges in 1/4″ and then fold in half with the long edges lined up and topstitch around all edges.
6. Center the handle on the non-zipper panel and topstitch each end in place with a barn door stitching pattern. You can either have the handle laying flat or you can scoot each end in a bit so the handle pops up. I think it’s a bit easier for little hands to grab if it’s sticking out some.
7. With right sides together sew your panels together along the short edges.
8. Topstitch next to the piping.
9. Carefully pin your finished panel to the bottom piece. If it’s a bit too big or small your can adjust by changing your seam allowances from step 7. If you measured carefully you should be good to go 🙂 Sew together right along the piping edge (I ended up using a 1/4″ seam allowance).
10. Unzip your zipper at least 6″ and then sew on the top panel. Turn right side out through the zipper opening.
11. Cut your foam out using a serrated knife. I ended up using 2 layers of foam for each cushion.